"PRO-STRIPE" Athletic Field Marking Paint
PRODUCT SPECIFICATIONS
--------------------------------------------------------------------------------
TYPE
Acrylic latex
--------------------------------------------------------------------------------
RECOMMENDED USE
For laying down lines or other markings on all types of athletic fields, football fields, soccer fields, volleyball courts,
golf courses and similar sports areas. "PRO-STRIPE" can also be used to line parking lots and curbs of concrete or
asphalt.
--------------------------------------------------------------------------------
COLOR
Colors supplied as a premix in White, Super White, and Soccer Yellow. Team colors and school colors are also
available and can be matched directly by the pantone color system. Do not tint.
--------------------------------------------------------------------------------
SHEEN
Flat
--------------------------------------------------------------------------------
PERCENT SOLIDS BY WEIGHT
99-2001:
40.5% ± 2.0%
99-2021:
54.3% ± 2.0%
99-2101:
37.6% ± 2.0%
--------------------------------------------------------------------------------
PERCENT SOLIDS BY VOLUME
99-2001:
24.9% ± 2.0%
99-2021:
35.0% ±2.0%
99-2101:
24.6% ±2.0%
--------------------------------------------------------------------------------
VISCOSITY
90-95 K.U. Stormer Viscometer
ENVIRONMENTAL STATEMENT
"PRO-STRIPE" Athletic Field Marking Paints are formulated to contain less than 0.06% lead in the dried film.
--------------------------------------------------------------------------------
PERFORMANCE FEATURES
"PRO-STRIPE" is made from the finest quality raw materials available. It has been tested and used by member
stadiums of MLB, NFL, NCAA, and World Cup Soccer.
--------------------------------------------------------------------------------
SURFACE PREPARATION
Grass should be cut to a low level (approx. 1" to 1½") on initial application to reach the ground. Apply when ground
is dry. When painting muddy areas, cover area with sand or clay to reduce runoff. Asphalt and concrete surfaces
should be cleaned of foreign debris, greases and oils. Do not paint if rain threatens or at temperatures below 50°F
(16°C).
--------------------------------------------------------------------------------
APPLICATION METHODS
Apply with a brush, marking machine, or spray (conventional and airless equipment). When applying with a brush or
roller, use PRO-STRIPE directly from the container. If applying by spray, thin with water to a consistency suitable for
spray equipment selected for application. Recommended dilution rate is two gallons of water to each gallon of
PRO-STRIPE. Do not mix more paint than will be used in a day. For best results when spraying use directly from the
container with minimal dilution. If fully diluted, spray PRO-STRIPE in one direction. When PRO-STRIPE dries, spray
the line in the opposite direction. Do not apply if rain threatens. If temperate weather is forecasted after painting,
cover the field with a water resistant tarp to prevent the paint from being "washed-out."
For best results when applying colors for logos first apply a base coat of PRO-STRIPE White. Allow 30 minutes to
dry and finish coat with the PRO-STRIPE color. This will assure maximum brilliance and color depth.
APPLICATION EQUIPMENT
Brush: Polyester/nylon brush recommended.
Roller:
All types of roller covers. Use at least a ½" nap roller cover.
Marking Equipment:
Airless Spray and Conventional Spray: Non-specialized spray equipment in a wide range of sizes and types can be
used.
Walk Behind Self Propelled and Push Type:
Jiffy Line Stripers models 5000, 7000, 7500, 8000, P-100 and 1000.
E-100 Battery Powered Striper
Newstripe Inc. Models, Fielder & Scotsman
--------------------------------------------------------------------------------
THINNING
Thinning is normally not required, water can be used as a diluent to reach a proper spraying consistency.
--------------------------------------------------------------------------------
DRYING TIME
77°F (25°C) and
50% relative humidity, to touch:
15 to 30 minutes*
*This condition does not mean that the paint film has reached full cure; handling can be achieved without loosening,
wrinkling, or otherwise marring the film under minimal pressure from fingers or hands. Drying times listed may vary
depending on temperature, humidity, and air movement.
--------------------------------------------------------------------------------
RECOMMENDED DRY FILM PER COAT
Spray and Marking Machines: 6 to 7 mils
Brush: 3 to 4 mils